how to change oil in honda gcv160 pressure washer

Honda'southward GCV 160 can be found in everything from pressure washers to lawn mowers, but whatever your motor is powering, information technology still requires the same maintenance. Here'southward what you demand to know to keep your Honda small engine running reliably for years to come.

Maintenance Schedule

Before each use: Check the air cleaner and the oil level.
Commencement month or 5 hours of functioning: Change the oil.
Every flavour or 25 hours: Clean the air cleaner
Every season or 50 hours: Change the oil, check the spark plug, and inspect the flywheel restriction pad.
Every 100 hours: Bank check the bract, restriction, clutch, and spark arrester (if equipped.)
Every 200 hours: Replace the air cleaner and spark plug.
Every two years: Check the fuel line for cracks and damage.

Honda recommends bringing this motor to a service eye for the following maintenance.
Every 100 hours: Cheque the valve clearance, fuel tank, and fuel filter.
Every 150 hours: Adjust the idle speed.

Fuel

This engine is designed to utilise standard automotive unleaded with an octane rating of 86 or college and no more 10% ethanol (E10) or 5% methanol. The tank should not be filled by the base of the filler cervix. When closing the tank, twist the fuel cap until it makes an audible click. Always motion the equipment at least 10 feet (three meters) away from the fueling location before starting to forbid the ignition of gas fumes.

Oil

Honda recommends 10W30, but 5W30 can also be used, or SAE 30 then long as temperatures are above 50 degrees F (10 degrees C.) This oil should meet API standard SJ or later.

To check the oil, remove the dipstick from the filler neck, wipe off any oil, and reinsert it without screwing it back into the neck. Remove the dipstick again and look for oil. If the oil is below the everyman mark on the dipstick, more oil should exist added.

To modify the oil, make sure the fuel valve is prepare to "OFF," remove the dipstick, and tilt the engine, letting the oil bleed into a container for recycling. Once the oil has drained, tilt the engine dorsum then that it's level and add fresh oil. Reinstall the dipstick.

Air Cleaner

The filter can exist accessed past pushing in on the tabs at the top of the cover and swinging the cover downwardly.

To make clean the filter chemical element, tap it against a hard surface to loosen dirt or blow it out using compressed air with a pressure of 30 psi or less. Wipe out any clay within the cover earlier reinstalling the filter.

Spark Plug

Annotation that in that location are two spark plugs specified for this engine. The 1 yous'll need depends on whether or not it'south being used to power a pressure washer.

To admission the spark plug, remove the spark plug cap and unscrew the plug using a spark plug wrench. The plug should be replaced if it's fouled, has a cracked insulator or worn electrode or is otherwise damaged.

The spark plug gap should be set to betwixt 0.028 and 0.030 inches (0.seventy to 0.eighty mm.)

When installing, make certain the sealing washer is at the base of operations of the threads. The plug should first exist screwed in past paw to preclude cross-threading, then tightened down with the plug wrench. Turn the plug 1/8-1/4 plough subsequently it seats if it has been used. New plugs should be turned 1/2 plough after seating to compress the washer.

Flywheel Restriction Inspection

To admission the restriction, start by removing the three flange nuts on the top of the recoil starter. Remove the recoil starter from the engine.

Next, slide the fuel tank off of the engine without disconnecting the fuel line. If at that place'southward fuel in the tank, fix information technology next to the engine while keeping it level.

The flywheel restriction is located side by side to the flywheel and has a large spring attached to it. The restriction shoe will need to be replaced if it's less than 3 mm thick. Honda recommends having this done at a service center.

Reinstall the tank and recoil starter in reverse society, making sure there are nonetheless 3 spacers on the studs that pass through the tank to concur everything in the correct position.

Spark Arrester

The arrester is an optional slice of equipment, but it can be added to whatever GCV160 to encounter local burn regulations.

To access information technology, remove the 3 6mm bolts holding on the muffler protector, so remove the screw holding the arrester inside the muffler. Use a wire brush to remove any carbon buildup. The spark arrester should exist replaced if it has whatever holes or cracks. Reinstall in reverse gild.

Getting Parts for Your GCV 160

When you lot need parts for Honda small engines, visit www.hondalawnparts.com. We're a certified Honda dealer, and we can ship OEM replacements for anything on your motor to any accost in the U.Southward. and Canada.

Source: http://blog.hondalawnparts.com/honda-gcv-160-maintenance-guide/

Posted by: davisonsert1961.blogspot.com

Share this post